1.  Accueil
  2. Produits
  3. Accessoires pour outils électroportatifs
  4. Scies-cloches,Scies-cloches,Scies-cloches,Scies-cl
  5. 427644
main image

427644

Scie trépan réglable

€ 18.26 PRIX H.T.
  • Corps en alliage d'acier
  • Pour percer dans le bois, les plaques de plâtre et le plastique
  • Profondeur de coupe max. de 30 mm
  • Vitesse max. de 500 min-1
  • À utiliser avec une perceuse électrique ou un support manuel
Évaluez ce produit review Logo
4 étoiles sur 5
16 évaluations

Caractéristiques techniques du produit

Matériau - construction secondaire N/A
Longueur de la tige N/A
Finition Peint
Matériau - abrasif Acier rapide HSS
Poids du produit 0,391 kg
Liant de l'abrasif Brasé

Manuels

Caractéristiques principales

Permet de percer rapidement et facilement des trous dans le bois, les plaques de plâtre et le plastique. Conception à 2 lames. Profondeur de coupe maximale de 30 mm. Idéale pour faire des trous pour les installations électriques, les tuyaux et les évents. À utiliser avec une perceuse électrique ou un support manuel.


Contenu

  • 1 x scie trépan réglable
  • 1 x clé hexagonale
  • 1 x foret

Évaluations de clients

par : Matthew H

2018-11-13T00:00:00

This is a great product, it takes a little time to get the hang of using it, but with a couple of practice cuts all is good. I cut all holes prior to fixing boards as this tool could be pretty messy used upside down! Done right cuts perfectly every time.

par : Alisdair B

2018-11-10T00:00:00

This saves a lot of money and gives a good precise result. No need for lots of different sizes

par : Artzt M

2018-10-03T00:00:00

Everything'' s good

par : Stewart

2018-03-05T00:00:00

Useful tool to cut/mark large holes..

par : Kelvin G

2017-11-17T00:00:00

Needed to cut some large holes in some timber. Cut them without any problem. Just don''t go too fast and make sure you have a firm grip on the drill.

par : Simon S

2017-02-26T00:00:00

Works well once you get the hang of using it. Can be tricky to set up the two heads as there are no specific location marks. I find it''s best used on a flat horizontal surface if possible.

par : Steven D

2017-01-15T00:00:00

I bought a new acrylic bath without tap holes so i needed to get a hole cutter to enable me to fit my taps. When i saw this hole cutter which is adjustable and not too expensive i thought I''''ll give it a go, once i marked my holes i applied the cutter, and to my surprise it made such light work of making 3 holes. Great tool for the job, glad i bought one.

par : Keith W

2016-11-19T00:00:00

dose just what it says on the packet, great!

par : raymond g

2016-10-10T00:00:00

good tool came in useful on other projects

par : Luis

2016-10-10T00:00:00

Una herramienta perfecta para hacer agujeros para empotrar luminarias, sencilla y facil de utilizar, con pocas vibraciones a la hora de hacer el agujero

par : Mr K

2016-09-27T00:00:00

Does the job well made and effective with an excellent Silverline guarantee.

par : terry b

2016-09-05T00:00:00

handy piece of kit

par : Bill

2016-09-01T00:00:00

Does not work very well. Wobbles everywhere. Drifts off centre. Not well balanced at all. Tried to cut 200mm holes but had to do them manually with a pad saw in the end. Tried using it with various drills at both high speed and low speed, got the same crap results. This was just in plasterboard, hate to think what it would be like in harder material. What a complete waste of money and time.

par : Martin S

2020-05-27T00:00:00

There''s a lot of bad reviews about this product but these seem to be by people who don''t seem to understand how it works rather than the product itself. This is ultimately a failure of the manufacturer to provide any instructions either with the product or online about the correct and safe use of this tool. Firstly, its worth understanding how the tool is designed to work as this will allow you to set it up correctly to get a effect desired. Looking at the tool you''ll notice that the two cutting blades are actually different from one another. One blade will cuts through the material at the actual circumference of the hole required (the outer cutter) whilst the other cuts through the material at a slightly smaller circumference (the inner cutter) thereby allowing the outer cutter to continue to penetrate the material beyond the depth of the tip of the blade where it is affixed to the blade holder. This applies equally to the inner cutter so they work in tandem to facilitate each other passing through the work-piece. It is essential therefore to set up the inner and outer cutters appropriately - I used a vernier caliper for accuracy e.g. for a 100mm diameter hole you would use the caliper to set an outer cutter distance of 54mm from one side of the 8mm pilot drill to the outer side of the outer cutter (i.e. for a cutting radius 50mm it''s 100/2 = 50mm + 8/2 = 54mm). For the inner cutter use the caliper to set an inner cutter distance of 54mm from one side of the 8mm pilot drill to the outer side of the inner cutter blade carrier - NOT the inner cutter blade itself! It''s also worth noting that it''s better to pilot drill your hole centre with an 8mm drill before attempting to use this tool and replace the supplied 8mm pilot drill bit with piece of 8mm plain bar (I just turned the supplied drill bit round so the smooth shank would insert into the pre-drilled pilot hole to guide the tool through the material. If you don''t do this using this tool in a hand drill for anything other than plasterboard or the like the cutters may catch and pivot the drill bit into the pilot hole thereby opening the pilot hole up and causing further catches etc, etc. Next, using an appropriate speed and drill - cut slowly perpendicular to the material let the cutting bits "nibble" away at the material. Remember the fact that you''re using this tool probably means you''re cutting large holes and the bigger the diameter the higher speed the cutting bits will be travelling at. A 3000 RPM drill speed equates to a cutter speed of in excess of 1.35km/h - if the bit catches and stops suddenly then that energy has to go somewhere... choose a drill that has low torque or even a torque clutch driver. One thing even I don''t understand is the purpose of the inclusion of the 6mm diameter point supplied with the tool - when inserted in the tool this is too short to even touch the work-piece surface!

par : JOHN

2019-07-22T00:00:00

Allen key that came with it snapped on very first use! Accuracy of gauge for each cutting blade is questionable to get them both set at the same distance!! suggest trial cut in spare piece of material to see if blades are equally set! A bit unwieldy to use !! A question of balance of the large rotating crossbar in comparison to using a rigid a hole-saw.It sort of worked ok !! I suppose as the speaker I was fitting had a reasonably large flange. If you need to have a variable diameter of cut and don''t wish to buy a hole saw set!! It''s a proposition. With hindsight I believe I should have just bought a 200mm good quality hole saw for the the one off job . At a similar price!

par : Wilbert G

2019-04-10T00:00:00

Great tool, cuts like a hot knife through, just be aware of the kick on your drill start on low speed.
Silverline Guarantee

Garantie à vie

Ce produit Silverline est garanti pendant une période de 30 jours à partir de la date d'achat contre tout vice de matériaux ou défaut de fabrication. Vous pouvez obtenir une garantie à vie en enregistrant votre produit en ligne. Tout bien présentant un défaut sera réparé ou remplacé gratuitement.

Les clients qui ont visualisé ce produit ont également consulté...
  • 447132
  • 633706
  • 633729
  • 633732
  • 675180